One way to control the traffic at busy intersections is to construct a roundabout or rotary intersection, which is a special type of at-grade intersection, where all converging vehicles are forced to move round a central island in clock-wise direction. The present study aims to design a rotary for an uncontrolled multi leg intersection located in Royapetah in Chennai, India. The intersection has five approach roads with two-way traffic in all the approach roads and there is no signal or traffic police to control the traffic at present and hence experiences traffic chaos during peak hours. In order to design the rotary, it is essential to have the information on traffic volumes coming from the approach roads. For this, a video data collection was carried out for a duration of eight hours from 7.30 am to 11.30 am and from 2.30 pm to 6.30 pm on a typical working day using a handycam from the terrace of an apartment building located near the intersection. During data extraction stage, each 5 min. traffic volume was extracted for all the five classes of vehicles considered and were converted to passenger car units (PCU). The analysis of traffic data showed that during peak hour from 4.45 pm to 5.45 pm, the proportion of weaving traffic, i.e., ratio of sum of crossing streams to the total traffic on the weaving section was found to be 0.81. According to Indian road congress (IRC) guidelines, this proportion can take any value between 0.4 and 1 and in the present study, the calculated value is found to be within the prescribed range. Using the calculated values of average entry width of the rotary and width & length of weaving section, the practical capacity of the rotary was found to be 3020 PCUs which is well above the observed traffic volume of 2665 PCUs.
Content may be subject to copyright.
Discover the world's research
- 20+ million members
- 135+ million publications
- 700k+ research projects
Join for free
IOP Conference Series: Materials Science and Engineering
PAPER • OPEN ACCESS
Design of a rotary for an uncontrolled multi-leg intersection in Chennai,
India
To cite this article: S. Vasantha Kumar et al 2017 IOP Conf. Ser.: Mater. Sci. Eng. 263 032030
View the article online for updates and enhancements.
This content was downloaded from IP address 191.101.83.61 on 04/12/2017 at 00:25
1
Content from this work may be used under the terms of the Creative Commons Attribution 3.0 licence. Any further distribution
of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI.
Published under licence by IOP Publishing Ltd
1234567890
14th ICSET-2017 IOP Publishing
IOP Conf. Series: Materials Science and Engineering 263 (2017) 032030 doi:10.1088/1757-899X/263/3/032030
Design of a rotary for an uncontrolled multi-leg intersection in
Chennai, India
S. Vasantha Kumar, Himanshu Gulati and Shivam Arora
School of Civil and Chemical Engineering, VIT University, Vellore – 632014, Tamil
Nadu, India.
Email: svasanthakumar@vit.ac.in
Abstract. One way to control the traffic at busy intersections is to construct a roundabout or
rotary intersection, which is a special type of at-grade intersection, where all converging
vehicles are forced to move round a central island in clock-wise direction. The present study
aims to design a rotary for an uncontrolled multi leg intersection located in Royapetah in
Chennai, India. The intersection has five approach roads with two-way traffic in all the
approach roads and there is no signal or traffic police to control the traffic at present and hence
experiences traffic chaos during peak hours. In order to design the rotary, it is essential to have
the information on traffic volumes coming from the approach roads. For this, a video data
collection was carried out for a duration of eight hours from 7.30 am to 11.30 am and from
2.30 pm to 6.30 pm on a typical working day using a handycam from the terrace of an
apartment building located near the intersection. During data extraction stage, each 5 min.
traffic volume was extracted for all the five classes of vehicles considered and were converted
to passenger car units (PCU). The analysis of traffic data showed that during peak hour from
4.45 pm to 5.45 pm, the proportion of weaving traffic, i.e., ratio of sum of crossing streams to
the total traffic on the weaving section was found to be 0.81. According to Indian road
congress (IRC) guidelines, this proportion can take any value between 0.4 and 1 and in the
present study, the calculated value is found to be within the prescribed range. Using the
calculated values of average entry width of the rotary and width & length of weaving section,
the practical capacity of the rotary was found to be 3020 PCUs which is well above the
observed traffic volume of 2665 PCUs.
1. Introduction
The problem of traffic congestion and ways to tackle needs to be addressed urgently in major urban
areas of India. The exponential growth of personal vehicles, combined with increase in trips and trip
lengths are the major reasons for traffic congestion in India. In Chennai, the total personal vehicle
population has increased from 10 lakhs in 1999 to almost 32 lakhs in 2011. This accounts for about
220 percent rise in the last 12 years. The increase of personal vehicles on urban roads not only causes
traffic congestion, but also leads to safety issues. The anticipated average journey speed on major
corridors in cities with population more than 80 lakhs (category-1a) will be 9 kmph and in cities with
population 40-80 lakhs (category-1b) will be 10 kmph in the year 2021 [1]. In 2031, the situation will
be even worse with anticipated speeds of 6 and 7 kmph, respectively. The master plan for Chennai for
the year 2026 is aiming for a modal split of 70:30 (Public transit: Personal vehicles) against the modal
split of 35:65 in 2009 [2]. The decreasing use of public transport further exacerbates the congestion
situation.
2
1234567890
14th ICSET-2017 IOP Publishing
IOP Conf. Series: Materials Science and Engineering 263 (2017) 032030 doi:10.1088/1757-899X/263/3/032030
According to Indian Road Congress (IRC) guidelines (IRC-65, 1976), a rotary can be of either
circular, elliptical, oval, rectangular shape with four approach roads/legs or it can be of complex
intersection with many approaches [3]. Most of the existing studies [4-7] on design of a new rotary or
capacity analysis of an existing rotary are mainly concentrated on intersections having only four legs
that intersect at nearly equal angles. The procedure for design of such rotaries having only four legs
intersecting at right angles is simple and straightforward as given in IRC guidelines [3]. However
studies on design of a complex rotary intersection with many approach roads have not been reported in
India. Hence the present study aims to design a rotary for an uncontrolled multi leg intersection
located in Royapettah in Chennai, India. The selected intersection has five approach roads as shown in
Fig.1. The Royapettah high road, Lloyd's road and Masilamani road are intersecting at the junction
and two-way traffic exists in all the approach roads. Currently there is no signal or traffic police to
control the traffic and hence experiences traffic congestion during peak hours. In order to design the
rotary, it is essential to have the information on traffic volumes coming from the approach roads. For
this, a video data collection was carried out, the details of which are presented in the following section.
Figure 1. Map showing the study location
2. Data collection and extraction
The video data collection was carried out to obtain the current traffic volumes, which is the main input
in design of a rotary. The data collection was carried out for a duration of eight hours from 7.30 am to
11.30 am in the morning and from 2.30 pm to 6.30 pm in the evening on a typical working day using a
handycam from the terrace of an apartment building located near the intersection. A snapshot of the
video collected is shown in Fig.2. As there is no signal or traffic police to control the traffic, the
intersection experiences traffic chaos during peak hours. During data extraction stage, each 5 min.
traffic volume was extracted for all the five classes of vehicles considered, namely, two-wheeler,
three-wheeler, passenger cars, light commercial vehicles (LCV) and heavy commercial vehicles
(HCV). A total of 20 directions of traffic movements were considered while extracting the 5 min.
traffic volume data. The directions considered are shown in Table 1. The class-wise traffic volumes
observed from video were converted to passenger car units (PCU) using the PCU factors suggested in
IRC guidelines [3]. The PCU factors used were 0.75 for two-wheeler, 1 for three-wheeler, passenger
cars, LCV and 2.8 for HCVs. The number of PCUs in each of the one hour duration, i.e., 7.30 to 8.30
am, 7.35 to 8.35 am, etc. was calculated till 11.30 am to find out the morning peak hour volume. In the
3
1234567890
14th ICSET-2017 IOP Publishing
IOP Conf. Series: Materials Science and Engineering 263 (2017) 032030 doi:10.1088/1757-899X/263/3/032030
same way, each one hour traffic volume from 2.30 pm onwards was calculated to identify the peak
hour volume in evening hours. Since it is difficult to identify the vehicles from video after 6.30 pm,
the evening data was restricted upto 6.30 pm. The observed peak hour volumes were used for design
of the rotary, the details of which are explained in the following section.
Figure 2. Snapshot of the video showing vehicles coming from different approach roads at the selected
intersection
Table 1. Observed traffic movements at the selected intersection.
Royapetah High Road (south)
Royapetah High Road (north)
Royapetah High Road (south)
Royapetah High Road (north)
Royapetah High Road (south)
Royapetah High Road (north)
Royapetah High Road (north)
Royapetah High Road (south)
Royapetah High Road (south)
Royapetah High Road (north)
4
1234567890
14th ICSET-2017 IOP Publishing
IOP Conf. Series: Materials Science and Engineering 263 (2017) 032030 doi:10.1088/1757-899X/263/3/032030
3. Identification of peak hour traffic volume
The hourly traffic volumes from 7.30 am to 11.30 am and 2.30 pm to 6.30 pm are shown in Fig.3 and
4 for morning and evening hours respectively.
Figure 3. Hourly traffic volumes between 7.30 am and 11.30 am
Figure 4. Hourly traffic volumes between 2.30 pm and 6.30 pm
It was found that, from 9 am to 10 am, the traffic volume was 4500 PCUs, which is the maximum
when compared to other hourly volumes during morning hours. Similarly during evening hours,
between 4.45 pm and 5.45 pm, a maximum traffic volume of 4535 PCUs was observed. Thus the
results showed that the maximum traffic volume during the eight hours study period was 4535 PCUs
and that has been used in the design of the rotary as explained in the following section.
4. Design of rotary intersection
The design of rotary for the selected intersection is performed following the IRC guidelines [3]. The
first step in design is to identify the peak hour traffic volume and for the present case study
intersection, it was found to be 4535 PCUs. The direction-wise traffic volume in PCUs is shown in
Fig. 5. It can be seen that the number of vehicles travelling in Royapetah high road is very high, i.e.,
936 PCUs from north to south and 611 PCUs from south to north. Similarly the number of vehicles
proceeding towards Lloyd's road west from north of the Royapettah high road is high as seen in Fig. 5.
5
1234567890
14th ICSET-2017 IOP Publishing
IOP Conf. Series: Materials Science and Engineering 263 (2017) 032030 doi:10.1088/1757-899X/263/3/032030
Figure 5. Direction-wise traffic volume in PCUs
The next step is to determine the inflow and outflow volumes in each of the approach roads. The
results are shown in Fig.6. It can be seen that the sum of inflow and outflow was found to be
maximum in the Royapettah high road (north), i.e., about 2665 PCUs. According to Kadiyali [8], the
practical capacity of the rotary should be more than this value for the design to be satisfactory.
Figure 6. Inflow and outflow volumes in each approach road
The third step is to find out the diverging, merging and weaving traffic from each of the five approach
roads as shown in Fig.7. This helps to find out the section where the proportion of the weaving traffic
, i.e., ratio of sum of crossing streams to the total traffic is maximum. For
the present intersection, the maximum proportion was found to occur between Royapettah high road
(south) and Lloyd's road (west). That is,
6
1234567890
14th ICSET-2017 IOP Publishing
IOP Conf. Series: Materials Science and Engineering 263 (2017) 032030 doi:10.1088/1757-899X/263/3/032030
According to IRC guidelines [3], the proportion can take any value between 0.4 and 1 and in the
present study, the calculated value is found to be within the prescribed range.
Figure 7. Diverging, merging and weaving traffic from each of the five approach roads
The next step is to calculate the practical capacity the rotary can handle for the given geometric
conditions and proportion of weaving traffic to total traffic. The empirical formula to calculate the
capacity of the rotary is given below [3].
Where, is the practical capacity of the weaving section of the rotary in PCUs/hr, is the width of
the weaving section, is the average entry width of the rotary and is the length of the weaving
section and is the proportion of the weaving traffic, i.e., ratio of sum of crossing streams (sum of b &
c) to the total traffic (sum of a, b, c and d) on the weaving section. For the present case, the proportion
of weaving traffic was calculated as 0.81. Using the maximum width of the approach road (10.36m),
the average entry width of the rotary was found to be 7.48 m and width of the weaving section as
10.98 m. According to IRC-65:1976, the weaving length should be at least 4 times the width of the
weaving section. Thus the weaving length for the present study was calculated as 44 m. Using the
above values of average entry width of the rotary, width & length of weaving section, proportion of
weaving traffic, the practical capacity of the rotary using equation (1) was calculated as 3020 PCUs
which is well above the maximum value of sum of inflow and outflow volumes, i.e., 2665 PCUs.
Hence the design can be considered adequate to handle the present approach traffic volumes. Finally,
the drawing of the proposed rotary intersection was prepared using AutoCAD as shown Fig.8.
7
1234567890
14th ICSET-2017 IOP Publishing
IOP Conf. Series: Materials Science and Engineering 263 (2017) 032030 doi:10.1088/1757-899X/263/3/032030
Figure 8. AutoCAD drawing showing the proposed rotary intersection
5. Conclusion
The Rapid urbanization is a serious issue faced by most of the metropolitan cities in India. Many
people are migrating from rural to urban areas and this urbanization results in the increase in number
of vehicles plying on the road. Though the vehicular growth follows an exponential trend, the
infrastructure expansion does not commensurate at the same level, thus results in traffic congestion on
city roads. Less usage of public transport further aggravates the congestion situation. One way to
control the traffic at busy intersections is to construct a roundabout or rotary intersection. Most of the
existing studies on design of a new rotary or capacity analysis of an existing rotary are mainly
concentrated on intersections having only four legs that intersect at right angles. However studies on
design of a complex rotary intersection with many approach roads have not been reported in India.
Hence in the present study, design of a rotary for an uncontrolled multi leg intersection located in
Royapettah, Chennai was attempted. Traffic volumes coming from different approach roads were
collected using videographic techniques and analyzed for peak hour traffic volume. Using that, the
design of the rotary following IRC guidelines was attempted and finally a drawing showing various
design elements for the proposed rotary intersection was prepared using AutoCAD software. When
compared to grade separators, constructing a rotary is a cheap and effective solution.
6. References
[1] CMDA 2008a Study on traffic and transportation policies and strategies in urban areas in
India - Final Report Chennai Metropolitan Development Authority, Chennai, India.
8
1234567890
14th ICSET-2017 IOP Publishing
IOP Conf. Series: Materials Science and Engineering 263 (2017) 032030 doi:10.1088/1757-899X/263/3/032030
[2] CMDA 2008b Second Master Plan for Chennai Metropolitan Area 2026 Chennai Metropolitan
Development Authority, Chennai, India.
[3] IRC: 65 1976 Recommended Practice for Traffic Rotaries Indian Roads Congress, New Delhi,
India.
[4] Chandra S and Rastogi R 2012 Mixed traffic flow analysis on roundabouts Journal of the Indian
Roads Congress Paper number 575 69-76.
[5] Patel M 2014 Solution for reduction of traffic congestion: a case Study of Thaltej rotary
intersection International Journal of Applied Engineering and Technology 4(1) 37-45.
[6] Mallikarjuna R 2014 Operational Analysis of Roundabouts under Mixed Traffic Flow Condition
M.Tech Thesis Department of Civil Engineering, National Institute of Technology, Rourkela,
India.
[7] Damor M N, Prajapati H C 2014 An evaluation of capacity of roundabout: A case study of
Anjali roundabout at Ahmedabad International Journal of Emerging Technology and Advanced
Engineering 4(2) 149-151.
[8] Kadiyali L R 2000 Traffic engineering and Transport Planning Khanna Publishers, New Delhi,
India.
... Then it happened will only cause problems opening a new problem-solving for citizens that the area was settled and could even reduce the quality of life of citizens [6,7]. Social Balance is one of the concepts that are offered to answer the problems above, where buildings and facilities therein to provide positive impact to the society around them, by way of share various things, from the use of facilities, and activities [8,9]. The expected goal is because the feeling of mutual need, and having one another among the lives around it is expected that uniqueness will attract buyers to other dwellings rather than ordinary residences and finally the selling price increases because of the nature of creating adjacent areas, growing together and integrate with each other [10]. ...
- Linna Ismawati
- F Faturahman
The purpose of this study is to increase the selling value of apartments, with the concept of social balance that is expected to be made to develop and grow in the environment around them with the power of synergy that will have an identity or characteristic. In this study, the authors used descriptive methods carried out in the literature and descriptive approaches to determine the success of the study, as well as references from previous studies. The results of this study are to make buildings that are not selfish and care for the community, especially those who live in apartments and generally the surrounding community. With the concept of social balance, the synergy between the two who become identities will be created while increasing the value of the apartment because of the value that other apartments do not have.
Operational Analysis of Roundabouts under Mixed Traffic Flow Condition M
- R Mallikarjuna
Mallikarjuna R 2014 Operational Analysis of Roundabouts under Mixed Traffic Flow Condition M.Tech Thesis Department of Civil Engineering, National Institute of Technology, Rourkela, India.
Traffic engineering and Transport Planning Khanna Publishers
- L Kadiyali
Kadiyali L R 2000 Traffic engineering and Transport Planning Khanna Publishers, New Delhi, India.
Department of Civil Engineering, National Institute of Technology) Operational Analysis of Roundabouts under Mixed Traffic Flow Condition M
- R Mallikarjuna
An evaluation of capacity of roundabout: A case study of Anjali roundabout at
- M N Damor
- H Prajapati
Damor M N, Prajapati H C 2014 An evaluation of capacity of roundabout: A case study of Anjali roundabout at Ahmedabad International Journal of Emerging Technology and Advanced Engineering 4(2) 149-151.
Solution for reduction of traffic congestion: a case Study of Thaltej rotary intersection
- M Patel
Patel M 2014 Solution for reduction of traffic congestion: a case Study of Thaltej rotary intersection International Journal of Applied Engineering and Technology 4(1) 37-45.
Mixed traffic flow analysis on roundabouts
- S Chandra
- R Rastogi
Chandra S and Rastogi R 2012 Mixed traffic flow analysis on roundabouts Journal of the Indian Roads Congress Paper number 575 69-76.
Posted by: alitaalitabrecheeneer10264987.blogspot.com
Source: https://www.researchgate.net/publication/321487032_Design_of_a_rotary_for_an_uncontrolled_multi-leg_intersection_in_Chennai_India
0 Comments